The DCD806 is a hammer drill, and most of its work has had nothing to do with hammering. Framing, workbenches, shelving, cabinetry, light fixtures. It arrived in the DCK250QQ2 kit during a renovation and has stayed in hand ever since.
As an Amazon Associate I earn from qualifying purchases. A commission may be earned if you buy through this link, at no extra cost to you.
Why a hammer drill was the one to buy
A renovation asks a drill to do a lot of different things in one week. Pilot holes in framing on Monday, a run of cabinet screws on Tuesday, a hole through stone on Thursday. Buying a separate tool for each job means a pile of tools and a lot of switching. A hammer drill that also behaves like a regular drill-driver covers all of it with one tool on the belt.
That was the reasoning behind the DCD806. It turned out to be the right call, though the hammer function ended up as the smallest part of the story.
What comes in the kit
DeWalt lists the DCK250QQ2 with the DCD806 hammer drill, a DCF845 3-speed impact driver, two DCB2104 20V MAX XR 4Ah batteries, a charger, two belt hooks and a contractor bag. The drill has a brushless motor, two speeds, a 1/2 inch metal ratcheting chuck, an anti-rotation system with an indicator and a pivoting LED work light.

The pairing matters more than it looks on a spec sheet. The drill makes the holes and the impact driver sets the fasteners, so neither tool spends the day swapping bits. Two batteries means one is always charging while the other works. In a kit like this, the second battery is what keeps a job moving.
The contractor bag is the unglamorous part that earns its keep. Everything rides together, so the tools, the batteries and the charger travel as one load from the garage to wherever the work is.
Wood, mostly
Most of the work has been in wood. Framing, workbenches, shelving, cabinetry, mounting lights and the odd small job around the place. A hammer drill sounds like a tool for stone and nothing else, and that is the wrong way to think about it. This one comes off the hook constantly because it is light, portable and handles nearly everything.

The two-speed switch sits on top of the drill, next to the chuck. Low speed is for driving screws and drilling large holes, where torque matters. High speed is for small bits, where the drill needs to spin. After a few days the switch stops being something to think about, and the hand finds the right setting without a look.
Cabinetry is where a drill shows its manners. Screws going into hardwood cabinet frames punish a drill with no clutch discipline, because one extra turn strips the head or cracks the wood. The clutch on the DCD806 handled that work without drama.
Framing is the opposite job. Long screws, dense lumber, lots of repetition. The drill took it without complaint, and the chuck held bits without slipping.
The metal chuck
A 1/2 inch metal ratcheting chuck is a quiet feature. Bits go in tight and stay put, which matters more than it sounds when the work involves spade bits and long auger bits that twist hard against the chuck. The ratcheting action tightens the jaws as the chuck is turned by hand, so a bit seats firmly without a second tool.
Plastic chucks loosen over time, and a loose bit wanders off the mark. Nothing like that has shown up here.
Stone siding
Hammer mode got used when it was time to run wiring and mount outdoor lighting into the stone siding of the house. The drill shattered right through the stone with almost no extra effort.
That is the job a hammer drill is built for, and it is worth saying how little fuss it took. No leaning into the tool with a shoulder, no stopping every few seconds to let it recover. Flip the mode, set the bit against the stone, and the hole is there.
Stone is unforgiving about technique. A masonry bit wants steady pressure and a clean start, and the hammer action does the rest of the work. Holes for wiring and light mounts have to land in the right place, so a drill that does not skate off the face of the stone makes the whole job easier.
One battery, one day
On the 4Ah battery, a full day or more of ordinary work passes before it needs a swap. Drilling and driving in short bursts uses far less power than holding the trigger down continuously, and that describes most real work. A pilot hole here, a screw there, a pause to measure.
The second battery in the kit has mostly stayed on the charger as a reserve. That is the best outcome for a kit like this. A battery that never runs out mid-job is a battery nobody thinks about.
Clutch, balance and grip
The drill has never bound or stalled, and it has never stripped a screw. Power comes on smoothly, and the clutch settings do their job cleanly. DeWalt also lists an anti-rotation system with an indicator on the DCD806, but since the bit never bound, it never had to step in.
Balance and grip are spot on. Fatigue stays low through a day of on-and-off use, and the drill sits comfortably whether it is pointed at a wall or held overhead at a ceiling box. Weight matters most at the end of the day, when a heavy tool turns every hole into a chore. This one stays out of the way.
The LED work light helps in the places where the light is worst: inside cabinets, under shelving, behind framing. It lights up the spot the bit is aimed at, so there is no need to hold a flashlight in the other hand.
The belt clip
It would be bought again. The one change would be the metal belt clip, which could be sturdier or better shaped.

The clip shows at the base of the drill in this photo. A clip is a small thing until it is the only thing a tool is carried by. On a job that has a person climbing a ladder with a drill on the belt, it is the part that matters most, and it is the one part of the drill that could use a rethink.
Who this drill suits
For a homeowner in the middle of a project, or a contractor who wants one tool to do the framing, the cabinets and the occasional hole in stone, the DCD806 covers the range. Heavy concrete work calls for a rotary hammer, which is a different class of tool. For everything short of that, this drill has been enough.
The kit makes the case on price, too. A drill, an impact driver, two batteries and a charger arrive in one box, which is more useful than a bare tool and a battery bought separately.
Sources
- DeWalt DCK250QQ2 product page: https://www.dewalt.com/en-us/product/dck250qq2/20v-max-xr-2-speed-hammer-drill-impact-2-tool-combo-kit
- Amazon listing, DCK250QQ2 kit: https://www.amazon.com/dp/B0FKKKVN7M
